April 21, 2022

Refurbishing your entryway

Most homeowners hire a contractor to refurbish their entryway when it looks a little worse for wear. Let us refinish your front door.

Refurbishing your entryway
The refurbishing job isn’t difficult for a professional contractor with skills and experience in entryway restoration. Think we’re bluffing? Then check out this guide. It's the approach we will generally use to refinish your front door.

Before we start

We’ll carefully inspect the signs of wear and tear you are trying to reverse. A door that might have suffered warping due to temperature extremes cannot be saved by sanding. We might have to stain it for the signs of damage to disappear. We won’t ignore your door’s material of construction.While a solid wooden door might be damaged beyond repair with a few coats of paint, a metal door will become unrecognizable if subjected to sandpaper treatment. We know which method of refinishing is best for your door. 

Painted entryways

  • Removing and disassembling the door. We’ll open your entry door and place a door-stopper underneath it. Once we have removed the pins of all hinges, we’ll carry your door to a workstation. We’ll set up two sawhorses and cover them with a towel or padding. The covering will protect your door from getting scratches. Then, we’ll place the door on the sawhorses. We’ll disassemble all the hardware, including doorknobs, handles, kick plates, and security locks from the door. These will be repaired or replaced as necessary.
  • Sanding the old wood finish. We’ll attach a sheet of 80-grit sandpaper to a random-orbit sander and move it over the flat panels of the door in gentle, back-and-forth motions. We’ll peel away paint until the finish gives way to clear wood. Then we’ll repeat the process with 100-grit paper, smoothing the wood finish.
  • Polish the sanded wood. Next, we’ll replace the 100-grit paper with 120-grit or 220-grit paper and sand the same areas we smoothened in the previous step. This should make it extra smooth.
  • Hard-to-reach areas. The corners and curved decorative areas of the door cannot be sanded with a machine. We need to sand them by hand. Using a trapezoid- or teardrop-shaped blade, we’ll start scraping. These scrapers work for different profiles in the wood. While a teardrop-shaped scraper works best for narrower portions, a trapezoid-shaped scraper works well with flatter portions that are relatively easier to access.
  • Sand the wooden profiles with a sanding sponge. We’ll use 100-grit sandpaper for sanding the areas we have scraped in the previous step. It may not be possible for us to hand-sand some hard-to-reach places. If that’s the case, we may use specially designed sanding sponges to polish these surfaces.
  • Remove leftover sawdust from the surface. We’ll remove sawdust by wiping the door clean with a dry cloth. We’ll then use a vacuum cleaner to get a more thorough cleaning.
  • Painting. We’ll then proceed to the steps outlined in our Paint Surface Preparation article.
  • Reassembly. We’ll reassemble most of the hardware, including doorknobs, handles, kick plates, and upper locks from the door.
  • Reattach the door. We’ll carry your door back from our workstation to the front entryway, position it against its frame, and start inserting the hinge pins. Once we have reattached all the hinge pins, we align the door and reassemble any additional hardware. 

Stained wooden doors

  • Apply linseed oil. Linseed oil is a natural wood preservative that preserves and protects the wood’s surface. We’ll pour a small amount of it into a painter’s tray, lubricate a natural-bristle brush, and apply the oil over the curved portions, including stiles, horizontal rails, and moldings. Then we’ll apply it over the flat portions.
  • Apply stain . After making sure that the wooden door is dry to the touch, we’ll apply stain over both the inner- and outer-facing sides of the door. We’ll start by applying the stain on the curved portions, with the straight portions of the door coming afterward.
  • Apply a second coat of stain. We’ll give the first coat at least one day to dry and follow it up with another coat of stain.Then we’ll follow up with a clear finish on the third day.


Your entryway should make a great first impression on anyone visiting your home. The refurbishing process will take up to three days, but the results are worth waiting for.